Engine - GM (19433063)

GMMPN19433063
Sale Price$13,490.74
Save$2,595.2416.1% off
MSRP $16,085.98
Description :

E-ROD SYSTEMS HAVE IT ALL
Each E-ROD crate engine system carries an official California Air Resources Board (CARB) E.O. number and includes complete emissions equipment, along with the engine controller and harness needed to get the engine running. The primary elements of each kit include:

  • Chevrolet Performance crate engine
  • Engine control module
  • Exhaust manifolds
  • Catalytic converters
  • Mass airflow sensor and sensor boss
  • Oxygen sensors and sensor bosses
  • Air filter
  • Accelerator pedal
  • Evaporative emissions canister
  • Instruction manual
E-ROD LT1 6.2L SYSTEM
  • CARB EO#: (PENDING)
  • Horsepower: 455 @ 6,000 rpm
  • Torque: 465 lb.-ft. @ 4,600 rpm
Introduced on the seventh-generation Corvette Stingray and Gen 6 Camaro SS, the LT1 6.2L V-8 opened the next chapter in the long, historic legacy of the Small-Block engine. It is architecturally similar to the LS family of Small-Block engines, but with a unique block casting, cylinder head design, oiling system and more. It also combines advanced technologies including direct injection and continuously variable valve timing to support an advanced combustion system. Chevrolet Performance's new LT1 crate engine - offered with a wet-sump or dry-sump oiling system - and a controller specially designed for retro-fit applications is included. This is the first LT-based E-Rod system and the most technically advanced. It is also available in a Connect & Cruise package with a matched 4L75-E automatic transmission.
INSTALLATION NOTES
Engines shipped with high-pressure direct-injection fuel pump installed
Assembly does not include any electronics
Kit includes electronic throttle pedal, which is required for throttle input to the ECU
Intended for pre-1995 street vehicles or any off-road vehicle
Not intended for marine applications
Front-End Accessory Drive Kit can be ordered separately
8-bolt crankshaft flange
Shipped with 14" flexplate
BUILDER'S NOTE
To facilitate a complete E-ROD installation, the builder will need to source additional components to complete the assembly and get the vehicle running, including:
  • Fuel tank
  • Fuel lines (re-circulating or returnless)
  • Fuel pump - 58 psi (400 kPa) for LC9 and LS3 or 65 psi (450 kPa) for LSA
  • Fuel tank vent line from the tank to the evaporative emissions canister
  • Purge line from the canister to the engine purge solenoid
  • Air induction system that incorporates the mass airflow sensor
  • Exhaust system behind the catalytic converters.
All E-ROD engines require a front-end accessory drive system suitable to the vehicle. The instruction manual included with each kit offers recommendations for the accessory drive kit, as well as the transmission, gear ratios and more. Chevrolet offers several configurations of accessory drive systems to suit different applications; and each allows the installer to easily delete air conditioning.
Chevrolet Performance recommends the LS1 Engine Installation Guide P/N 88959384, which illustrates basic procedures and offers helpful tips on installing an LS engine into older vehicles.
E-ROD systems do not come with a transmission. Chevrolet Performance recommends the SuperMatic(TM) 4L70-E - P/N 19244043 - four-speed automatic overdrive transmission, along with Chevrolet Performance's SuperMatic(TM) transmission controller P/N 19257634, for LC9 and LS3 systems. The LSA, with higher torque output, should use the SuperMatic(TM) 4L85-E, P/N 19300175, along with the SuperMatic(TM) transmission controller, P/N 19302410.
*GM automatic transmissions are typically equipped with 40-tooth reluctor wheels for vehicle speed sensor output. GM late-model manual transmissions are typically equipped with a 17-tooth reluctor wheel. The Chevrolet Performance T56 Super Magnum six-speed manual (P/N 19329795) is equipped with a 40-tooth reluctor wheel.
You May Also Like
Bell Housing Kit LS and LT Engines
$860.52
Clutch Kit LS/LT Engines (8-Bolt Crank)
$1,714.42
LT1 Aluminum Automatic Bell Housing
$176.90

My Location
  • Min. 12 Months
  • Safe, Secure Checkout

Product Details

Description

E-ROD SYSTEMS HAVE IT ALL
Each E-ROD crate engine system carries an official California Air Resources Board (CARB) E.O. number and includes complete emissions equipment, along with the engine controller and harness needed to get the engine running. The primary elements of each kit include:

  • Chevrolet Performance crate engine
  • Engine control module
  • Exhaust manifolds
  • Catalytic converters
  • Mass airflow sensor and sensor boss
  • Oxygen sensors and sensor bosses
  • Air filter
  • Accelerator pedal
  • Evaporative emissions canister
  • Instruction manual
E-ROD LT1 6.2L SYSTEM
  • CARB EO#: (PENDING)
  • Horsepower: 455 @ 6,000 rpm
  • Torque: 465 lb.-ft. @ 4,600 rpm
Introduced on the seventh-generation Corvette Stingray and Gen 6 Camaro SS, the LT1 6.2L V-8 opened the next chapter in the long, historic legacy of the Small-Block engine. It is architecturally similar to the LS family of Small-Block engines, but with a unique block casting, cylinder head design, oiling system and more. It also combines advanced technologies including direct injection and continuously variable valve timing to support an advanced combustion system. Chevrolet Performance's new LT1 crate engine - offered with a wet-sump or dry-sump oiling system - and a controller specially designed for retro-fit applications is included. This is the first LT-based E-Rod system and the most technically advanced. It is also available in a Connect & Cruise package with a matched 4L75-E automatic transmission.
INSTALLATION NOTES
Engines shipped with high-pressure direct-injection fuel pump installed
Assembly does not include any electronics
Kit includes electronic throttle pedal, which is required for throttle input to the ECU
Intended for pre-1995 street vehicles or any off-road vehicle
Not intended for marine applications
Front-End Accessory Drive Kit can be ordered separately
8-bolt crankshaft flange
Shipped with 14" flexplate
BUILDER'S NOTE
To facilitate a complete E-ROD installation, the builder will need to source additional components to complete the assembly and get the vehicle running, including:
  • Fuel tank
  • Fuel lines (re-circulating or returnless)
  • Fuel pump - 58 psi (400 kPa) for LC9 and LS3 or 65 psi (450 kPa) for LSA
  • Fuel tank vent line from the tank to the evaporative emissions canister
  • Purge line from the canister to the engine purge solenoid
  • Air induction system that incorporates the mass airflow sensor
  • Exhaust system behind the catalytic converters.
All E-ROD engines require a front-end accessory drive system suitable to the vehicle. The instruction manual included with each kit offers recommendations for the accessory drive kit, as well as the transmission, gear ratios and more. Chevrolet offers several configurations of accessory drive systems to suit different applications; and each allows the installer to easily delete air conditioning.
Chevrolet Performance recommends the LS1 Engine Installation Guide P/N 88959384, which illustrates basic procedures and offers helpful tips on installing an LS engine into older vehicles.
E-ROD systems do not come with a transmission. Chevrolet Performance recommends the SuperMatic(TM) 4L70-E - P/N 19244043 - four-speed automatic overdrive transmission, along with Chevrolet Performance's SuperMatic(TM) transmission controller P/N 19257634, for LC9 and LS3 systems. The LSA, with higher torque output, should use the SuperMatic(TM) 4L85-E, P/N 19300175, along with the SuperMatic(TM) transmission controller, P/N 19302410.
*GM automatic transmissions are typically equipped with 40-tooth reluctor wheels for vehicle speed sensor output. GM late-model manual transmissions are typically equipped with a 17-tooth reluctor wheel. The Chevrolet Performance T56 Super Magnum six-speed manual (P/N 19329795) is equipped with a 40-tooth reluctor wheel.
You May Also Like
Bell Housing Kit LS and LT Engines
$860.52
Clutch Kit LS/LT Engines (8-Bolt Crank)
$1,714.42
LT1 Aluminum Automatic Bell Housing
$176.90


Part Number (MPN)
19433063
Brand
SKU
19433063
Superseded Part Number(s)
12682080, 19370671, 19418256

YearMakeModelBody & TrimEngine & Transmission
Vehicle #1
Year
Make
Model
Body & Trim
Engine & Transmission

Shipping Policy

  • In stock orders ship within 24 hours.
  • Weekend orders will be processed the next business day.
  • If a part is not in stock and must be ordered from the manufacturer, it usually takes 2-3 days to arrive to us and will be promptly shipped to you. Most of the orders are shipped complete within 2-3 business days. A few of the parts ordered from the manufacturer may take up to 5-6 business days to arrive and will shipped to you immediately.
  • Depending upon location, ground shipments usually take 2-7 days.
  • Your order may be shipped Overnight for an additional cost.
  • Oversized shipments will be additional; you will be contacted prior to shipping for approval.
  • We cannot guarantee transit times for ground and oversize orders.
  • Shipping Carrier substitutions may be made at our determination in an attempt to reduce shipping cost to the customer.
  • We do not ship internationally.
  • In the unlikely event that a part has been placed on backorder or discontinued, we will do our best to try and find one for you as quickly as possible.
  • We do not ship COD orders.
Check out our Shipping Policy for more details.

Return Policy

  • Contact us to arrange for any returns.
  • A copy of the invoice will need to be included with the return.
  • There is a 15% restocking fee charged against all returned parts.
  • Parts must be resaleable and in the original packaging.
  • We cannot take back used parts.
  • We cannot take back installed or tried parts.
  • Electrical parts are not returnable.
  • We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria.
  • Return request need to be within 30 days of receipt.

Cancellation Policy

  • An order or a portion of an order may be cancelled up until the time it is shipped and no longer in our possession.
  • If the cancelled part was special ordered from the manufacturer a return fee of 15% may apply.
Check out our Return Policy for more details.


Real OEM Parts World

Searching for somewhere you can trust purchasing genuine parts and accessories for your GM or MOPAR vehicle online? You’ve come to the right place! We’ve got the perfect parts and accessories made to fit the exact specifications of your vehicle. When it comes time for replacement parts, avoid needless delays.  We stock an extensive inventory of GM and MOPAR ​ parts and accessories, offering every kind of part and accessory you will need to dress up your car, SUV or truck, delivered right to your home. 

​